Make your Own DIY Wood Drying Kiln (Updated for 2026)
- David Condon
- Apr 22, 2023
- 11 min read
Updated: 5 days ago
So you've started this obsession known as Woodturning and after buying a Lathe and Hand Tools you are chomping at the bit to get Turning. Problem is that you've very little wood to work with and what you get is expensive or hard to get. You then read an article or watch a video where someone tells you that you can cut and dry your own wood for a lot less money and time. Easy and no fuss! Well, it's not exactly that simple and you have a bit of work ahead of you before you can do this correctly.
Before drying your timber, it’s worth reading my guide on how to process logs for woodturning , it covers how I cut, seal, and store rough blanks straight after felling.
Make your Own DIY Wood Drying Kiln
In this Post I will describe how I built and used my own DIY Kilns using retail glass front shop fridges. Any unit that is mostly insulated like Fridges, Dishwashers etc. will do but the bigger they are, the more wood you can dry at any one time. With my experience insights you may be able to set up your own system and dry wood for Woodturning faster and hopefully cheaper than buying off the shelves.
The image above was my first crude attempt getting a kiln off the ground. You can see different sizes of wood and species from hardwood to softwoods inside, I didn't know any better to be honest and I was rushing to dry wood.
Related Woodturning Resources & Practical Guides
If you’d like to go deeper into the wider woodturning process, I’ve written separately about how to process logs for woodturning and I also have a broader post called My Process: How I Approach Woodturning, From Log to Finished Piece, which ties the whole workflow together, based on how I approach preparation, drying, and turning in my own workshop.
Working with Irish hardwood is challenging but very rewarding. You’re always on the lookout for new logs, better ways to handle them, and safer methods that reduce strain on the body. Most of what I share here comes from trial, error, and adapting things in my own workshop over the years, rather than textbook theory.
I’ve also written a practical post on setting up a simple woodturner’s cutting bench, showing how I adapted my own setup to make cutting heavy logs safer, more controlled, and easier on the body. You’ll find that article, along with other in-depth woodturning guides, on my blog.
Disclaimer; You need to get expert advice on Electrics and Fire Safety!
Before getting into the practical details below, it’s important to be clear about safety and responsibility.
This post is not a definitive instructional manual. It’s a practical guide showing how I built and used my own kiln, based on real workshop experience. I’ll refer to safe practices throughout because working with a wood-drying kiln involves electricity, heat, and moisture, all of which can be dangerous if handled incorrectly.
Any electrical work should be carried out or checked by a qualified electrician. Make sure the unit is properly earthed using suitable earth wiring and an earth spike where required. Electricity and water are a dangerous combination, so professional advice is essential before you go any further.
Fire safety is equally important. Appropriate precautions should be in place near the kiln at all times, such as a fire extinguisher and fire blanket, to protect both the workspace and your home. Ultimately, you are fully responsible for your own setup and its operation. Saving a few euros on timber is never worth risking serious damage or costly repairs.
With that in mind, the sections below outline the practical considerations around housing, layout, and setup, based on what has worked for me.
Housing Requirements and Set Up
You’ll need a sheltered location to house the kiln, ideally an outdoor shed or lean-to that is weatherproof and well protected. Rain should not be able to reach the unit, and it’s worth remembering that rain doesn’t always fall straight down, wind can drive it sideways.
I initially housed my kiln under a lean-to roof outside my workshop. It worked well for a time, but as the workshop layout evolved and other equipment came in, I eventually relocated the kiln to different areas better suited to long-term use.
If possible, locate them away from your house or valuable property is advisable too. An available power socket, preferably waterproof is also necessary, I don't recommend stringing extension leads together to reach the kiln as this is not safe practice. Have a Smoke Alarm, Fire Extinguisher and Fire Blanket in close proximity to the kiln at all times to be prepared for any eventuality no matter how remote you think the possibility is.
Air Holes
I started by drilling 4 x 1'' holes in the floor and 4 x 50mm holes on the left and right up near the inside top of the kiln. I could have limited this to 1 x 50mm or 2 inch hole each side as 4 was total overkill. Most of the time the holes should be almost completely covered so that the warm air doesn't escape too quickly and a little drip of water should be visible there at all times during the first few weeks. A small hole each side would probably have been sufficient too and a control door much simpler to make. Too many holes
and you might case harden the wood.
In the early weeks of use, the kiln should always look wet with droplets all over the glass and walls of the kiln.
I also drilled holes in the floor so the warm air rising would pull in new fresh air which would in turn be warmed and circulated. There are many articles online that suggest drilling multiple large holes but I found that a few small ones do the job. You can always cover these holes if you find there is too much fresh air going in to the kiln. You can start off drilling one hole in the bottom and one each side and then experiment with each new load of wood. Drill more as required.
Metal Platform for trapping heat
This made sense to me after my first operation. I had Beech Bowls and some cracked on the lowest shelf because the heat from the bulb was too direct and severe. I got stainless steel platform trays made up with a downward lip on all 4 sides, in effect making an upside down receptacle. My thinking at the time, was that the tray would stop direct light from the bulb from reaching the wood and also allow heat to build up underneath the tray and dissipate more slowly. I think it worked like I planned. You can see the pan in the image above.
PC Fan
At the time I was experimenting with wind and solar power and I had a couple of deep cycle marine batteries set up. A buddy of mine gave me 2 large PC fans which worked a treat using the batteries. The PC fan had a low CFM rate and gently pushed the air from below. Too fast and too direct air current can cause micro cracks, especially in bowls.
Important; Bowls and blanks should have their endgrain sealed with glue before going into the kiln to slow down moisture loss. Always use stickers to keep an air gap around the wood at all times.
Light for Heat
I rigged up a standard light pendant at the rear of the kiln about 6 inches above the floor. I chose this height so as not to melt the floor of the unit. The floor is light metal sheeting with plastic and insulation underneath. See image above.
I found so many articles about DIY kilns that say start a greenwood load with a 40 watt bulb and increase to 60 watt after a week, eventually getting up to 100 watts. I saw no need to change the bulb at all and the kiln reached temperatures of 20 degrees Celsius and above quite easily. If you want it to get hotter, close the air vents even further. You could add a 60 watt bulb to begin with but that may get too hot and will cost more to run. Using a 40 watt bulb and allowing extra drying time would be far better for the wood you are drying. Slower is nearly always better when it comes to drying wood!
Glass Front Cover
I realized during early testing that the Glass Front was losing heat so I rigged up a cover of Marine Plywood with reflective insulating foil on the inside and a handle for easy removal. I also painted the lower end of the glass door to stop light reflecting back into the wood. This was a very effective and cheap solution.
Relative Humidity Monitor
You can buy battery RH devices and temperature monitors quite cheaply on eBay and though not 100% accurate should give you an indication of progress. During the first 2 weeks of operation there should be 100% Moisture Content in the kiln and it should drop slowly after that. Don't try and rush this by opening the vents. 1mm of air gap is probably more than enough on each side of the kiln. If the surface moisture on the fridge door starts to disappear too quickly you need to close the top air vents further or completely until the moisture returns. Sometimes the moisture will escape through the closed vent hole without any need to open the vents, it depends on the material you use for the door. You will have to experiment yourself to find the best way. I used 3mm or 1/8 inch plywood and it seemed to work fine.
Before Operating the Kiln
Before switching on for the first time I attached and Earth Cable to the metal frame close to the pendant and connected it to an Earth Spike driven into the ground close by. I asked an Electrician friend to double check everything was safe too. I didn't want to risk burning my workshop down so better to be safe than sorry. I have done plenty of wiring in my life but I always defer to a professional when there is any possible risk to life and property.
Operating the Kiln
When filling the kiln with wood, it is important to load the kiln with similar species and similar thicknesses. Don't put a 4 inch blank with a 2 inch blanks and expect them to dry over the same timeframe. Always use stickers to separate the wood and leave gaps all around for the air to circulate. Avoid overloading if you think it is interfering with airflow or gaps between wood.
Container of water
Greenwood needs moisture in order to start drying so it's important to add a container of water so the heat can raise the humidity to 100% for at least the first week or two. In my case, I filled a Chinese takeaway container and left it dead centre in the bottom of the kiln. The greenwood will release moisture too so it shouldn't run out too quickly. You can add a bigger container if you wish. The heat from the bulb and the air movement from the fan will evaporate the container after the first week or so and the kiln walls and floor should be saturated at this point. As long as you don't open the vents too much during the initial stages the wood should dry correctly from the inside out.
As Simple as that but not really. In the first few pictures you will see a mix of Leland Cypress, Ash and Yew. This was back when I didn't know what I was doing and having just built the units I was itching to try them out. Experience has taught me that you can't dry hardwoods and softwoods together and you shouldn't dry different thicknesses together either. Keep 2 inch stock with 2 inch stock and dry 4 inch stock with 4 inch stock. 4 inch planks would be better off being air dried for a year or two before using a kiln. If you intend 4 inch material for bowls then it would be better to rough Turn and seal them prior to using a kiln. Experimentation in the early stages of my business made things really exciting and most of the time I couldn't help but push forward even if it meant ruining some stock.
Takeaway
Being able to source Hardwood yourself can be a much better alternative to purchasing from a store. It takes time to make these things and perfect your methods. You will probably be a Woodturner for many years whether in business or hobby level so you have time to get it right. Drying wood is a slow process, don't be fooled by any online articles promising you fast results. Wood doesn't dry out like that.
The best wood drying method I have seen is from Glenn Lucas who uses an Arrowsmith dehumidifier to dry bowl blanks in an insulated container in approximately 6 weeks. After the initial 100% wet week, cycles of 1 hr dehumidification and 3 hours off at around 35 degrees dries the wood slow enough for the moisture to leave the inside cells without the wood cracking. I have had good results from my DIY kilns but I was not very experienced at wood drying at the time. For small scale Woodturners, this type of kiln might suit you. If you like to experiment, this is a good one to try.
If you’re interested in building your own kiln and got some benefit from this post, you might also enjoy my other post on turning waste wood shavings into briquettes — a simple way to put your offcuts and sawdust to good use.
One Last Option
I saw another woodcrafter who set up a household electric dehumidifier inside a glass front fridge like I have above. A section of the floor and underneath was cut away to allow the dehumidifier to sit into the base. As long as the machine air vents are not blocked and the machine is allowed to vent its operating heat this could be an option. Again, you should only operate this while you are in the room or the fridge is located as mentioned above and doesn't pose a risk to life and property.
Whatever system you use, please do it safely and get someone qualified to double check your work.
I hope this has been helpful. Happy and Safe Drying!!!!!
About the Author
I’m David Condon, a woodturner and small business owner based in Tralee, Co. Kerry. I’ve been working with wood for most of my life at this stage — 11 years as a carpenter and over a decade running my own woodturning business.
During that time, I’ve worked with Irish hardwoods, taught woodturning, and run my workshop full-time. On this site, I share the same knowledge I pass on to my students — from choosing the right wood and tools to finishing techniques that make every project shine.
I also stock a carefully chosen range of turning blanks, tools, and craft supplies that I use every day in my own work. You can explore more of my handcrafted pieces and classes at DavidCondonWoodcraft.ie.
© David Condon Woodcraft – All Rights Reserved.
☕ Buy Me a Coffee?
I used to run ads on my website to generate a small income, but they slowed things down and didn’t fit the feel of what I’m building here. So, I’ve removed them in favor of something simpler and more personal—a “Buy Me a Coffee” button.
If you found this post interesting, helpful, or simply enjoyable, feel free to use the link below to show your support. No pressure at all—but every little bit helps, and it’s always genuinely appreciated. As a small independent maker, I rely on a mix of teaching, crafting, and sharing to keep things going. This is just one way to help keep the shavings flying. Thanks so much!
More Woodturning Pages to Explore
● Hampshire Sheen - Fine Finishing products that will highlight your project pieces
● Hamlet Tools - Fantastic Woodturning Tools from a well trusted brand
● Woodcraft Hub - View my woodcraft creations for inspiration of gift buying.
● Sanding Essentials - Essential sanding products for Woodturners & Woodworkers.
● Woodturning Blanks - A fine range of Hardwood Spindle Blanks & a few Bowl Blanks too!
● Woodturning Pen Blanks - A huge assortment of Acrylic & Irish Hardwood Pen Blanks.
● Crafter's Haven – A vast range of craft supplies for crafters and gift givers!
Original content © David Condon Woodcraft — Written by David Condon. Please credit and link if shared.
Comments